Technical Guide

Stainless Steel Round Bar Size & Weight Chart (mm & kg per Meter)

A working round bar size chart for 3 to 100 mm diameters: theoretical kilograms per metre, weight per 6 m bar, the D² × 0.00623 formula and inch equivalents. Use it to estimate a load before the RFQ, then confirm the actual weight on the scale.

303 stainless steel round bars in stock, used for the size and weight reference
In This Guide
  1. Why Buyers Check Bar Weight Before the Quote
  2. Quick Answer: How Much Does a 20 mm Round Bar Weigh?
  3. Round Bar Size and Weight Chart (Metric)
  4. How the Weight Formula Works
  5. Imperial Sizes: Inch Round Bar Weight
  6. Density Differences: 304, 303 and 316L
  7. Theoretical Weight vs Actual Scale Weight
  8. Tolerance Does Not Change the Nominal Calculation
  9. How to Use the Chart in an RFQ
  10. Two Numbers to Remember
  11. Send the Size List

Why Buyers Check Bar Weight Before the Quote

Most round bar inquiries start with a diameter and a length, not a weight. The buyer needs to know whether 200 bars will fit a container, what a bundle weighs, or whether a price per kilogram is reasonable. That is where a reliable round bar size and weight chart saves time.

This chart covers the common 3 to 100 mm range, gives theoretical kilograms per metre and the weight of a 6 m bar, and explains the formula behind the numbers. It also covers the points that cause disputes later: density differences between grades, tolerance, and theoretical versus actual weight.

Quick Answer: How Much Does a 20 mm Round Bar Weigh?

A 20 mm 304 or 303 stainless steel round bar weighs approximately 2.49 kg per metre. A 6 m bar is about 14.95 kg. The same size in 316 or 316L is approximately 2.51 kg/m, or about 15.08 kg per 6 m bar.

For a 100-piece order of 20 mm × 6 m bars, the theoretical total is about 1,495 kg. Treat that as an estimate for logistics and budgeting, then confirm the actual weight with the supplier before shipment.

Round Bar Size and Weight Chart (Metric)

The table below uses a density of 7.93 g/cm³, which is the normal value for 304 and 303 stainless steel. Weights are rounded to two or three decimals; small differences in the last digit come from rounding, not from a different formula.

Diameter (mm)kg per metrekg per 6 m barkg per 10 × 6 m bars
30.0560.343.4
40.1000.606.0
50.1560.949.4
60.2241.3413.4
80.3992.3923.9
100.6233.7437.4
120.8975.3853.8
141.2217.3373.3
161.5959.5795.7
182.01912.11121.1
202.49214.95149.5
223.01518.09180.9
253.89423.36233.6
284.88429.30293.0
305.60733.64336.4
326.38038.28382.8
357.63245.79457.9
388.99653.98539.8
409.96859.81598.1
4512.61675.70757.0
5015.57593.45934.5
6022.428134.571,345.7
7030.527183.161,831.6
8039.872239.232,392.3
9050.463302.783,027.8
10062.300373.803,738.0
Bundled 304 stainless steel round bars in the warehouse
The chart is a theoretical reference; the packing list shows the actual bundle weight.

For diameters outside this range, or for cut lengths rather than 6 m bars, the same formula still applies. Substituting diameter and length is faster than looking for a second table.

This table is for round bar only. Hex, square and flat bar use a different area formula, so the figures above should not be applied to other shapes. If the drawing mixes round and hex sizes, calculate each line separately.

How the Weight Formula Works

The standard formula for round bar weight is:

Weight per metre (kg/m) = D² × 0.00623

D is the nominal diameter in millimetres. The coefficient combines the circular area and the density of stainless steel:

  • Area = π/4 × D² (mm²)
  • Volume per metre = area × 1,000 mm³
  • Mass = volume × 7.93 g/cm³

The result is 0.006229 × D² kg/m, which is normally shortened to 0.00623. For a 20 mm bar: 20 × 20 × 0.00623 = 2.492 kg/m.

For any length, multiply by the length in metres:

  • 1 m = 2.49 kg
  • 3 m = 7.48 kg
  • 6 m = 14.95 kg

This is the same calculation used by the round bar weight calculator, which is useful when the order mixes several diameters and lengths.

Imperial Sizes: Inch Round Bar Weight

Many drawings in Southeast Asia still use inch sizes, especially for maintenance and replacement parts. Convert the inch size to millimetres first, then apply the same formula.

Inch sizemmkg per metrekg per 6 m bar
1/8"3.1750.0630.38
3/16"4.7630.1410.85
1/4"6.3500.2511.51
5/16"7.9380.3932.36
3/8"9.5250.5653.39
1/2"12.7001.0056.03
5/8"15.8751.5709.42
3/4"19.0502.26113.57
7/8"22.2253.07718.46
1"25.4004.02024.12
1-1/4"31.7506.28037.68
1-1/2"38.1009.04554.27
2"50.80016.07596.45
3"76.20036.174217.04
4"101.60064.302385.81

Inch sizes are not exact metric equivalents. A 1" bar is 25.4 mm, not 25 mm, and the weight difference is about 3% at that size. If the drawing is in inches, keep the inch size through the PO and the inspection record.

Density Differences: 304, 303 and 316L

The figures use 7.93 g/cm³. Grade changes the number, but not by much:

GradeTypical densityCoefficient20 mm bar
304 / 304L7.93 g/cm³0.006232.49 kg/m
303 / SUS3037.93 g/cm³0.006232.49 kg/m
316 / 316L7.98 g/cm³0.006272.51 kg/m
Duplex 2205about 7.80 g/cm³0.006132.45 kg/m

For a single bar the difference is small. For a 20-tonne project order it is worth using the right grade value, especially when comparing suppliers who quote in different units.

Grade availability is a separate check. 303 is usually stocked for free-machining work, while 304 covers general machining and 316L covers corrosive service. Compare the 303 round bar and 316L round bar pages, or start from the stainless steel round bar range, before fixing the grade in the PO.

Theoretical Weight vs Actual Scale Weight

Two numbers can legitimately differ:

  • Theoretical weight comes from nominal diameter, nominal length and standard density. It is the normal basis for price comparison, container planning and RFQs.
  • Actual weight comes from the scale. It includes the real diameter, the real length, sawn end condition and bundle straps, and it may be recorded per bundle or per truck.

A 20 mm h11 bar can measure slightly below 20.000 mm, so a bundle may weigh a little less than the nominal calculation. That is normal. What matters is that the quotation states the basis and the packing list states the actual figure. If a supplier quotes per kilogram, ask whether the invoice follows theoretical or actual weight.

Tolerance Does Not Change the Nominal Calculation

Tolerance and weight are separate topics. h9, h10 and h11 describe the permitted size window around the nominal diameter; they do not change the nominal diameter used in the weight formula.

For a 20 mm bar, the h-series limits are:

GradeUpper limitLower limit
h920.000 mm19.948 mm
h1020.000 mm19.916 mm
h1120.000 mm19.870 mm

If the order needs a tight window, read the h9, h10 and h11 tolerance guide and use the tolerance lookup before writing the PO. Do not accept a weight table as evidence of diameter tolerance; they answer different questions.

How to Use the Chart in an RFQ

A weight estimate is only useful if the inquiry carries the details that affect supply:

  • Grade and standard: 303, 304, 304L, 316L; ASTM A276 or A582 where specified
  • Diameter and length: mm or inches, with the unit written out
  • Quantity: pieces or kilograms, and whether the figure is theoretical or actual
  • Tolerance and finish: h9/h10/h11, cold drawn, peeled, ground or polished
  • Cutting: mill lengths or cut-to-length, with end condition
  • Documents: MTC, heat number on labels, packing list
  • Destination port and trade term

When those details are in the first message, the supplier can check stock and confirm the route instead of asking for clarification three times. The bar quote page lists the same fields in a short form.

One more practical check: for mixed orders, calculate each line separately. Ten bars of 16 mm and ten bars of 25 mm do not weigh the same as twenty bars of 20 mm, even though the total length is identical.

Two Numbers to Remember

For a quick field estimate, remember two numbers: 20 mm 304 bar ≈ 2.49 kg/m, and a 6 m bar ≈ 14.95 kg. For other diameters, square the millimetre size and multiply by 0.00623. Use the chart to plan the load, then confirm the actual weight and the settlement basis with the supplier before the order ships.

Frequently Asked Questions (FAQ)

Q. How much does a 20 mm stainless steel round bar weigh?

A. About 2.49 kg per metre for 304 or 303, or 14.95 kg for a 6 m bar. In 316L it is about 2.51 kg/m.

Q. What is the formula for round bar weight per metre?

A. D² × 0.00623, with D in millimetres. For 316L, use 0.00627 because the density is higher.

Q. Does the chart also work for 316L and other grades?

A. Yes, with the correct density. 316/316L is about 0.6% heavier than 304 at the same diameter; duplex needs its own value.

Q. Does h9 or h11 tolerance change the calculated weight?

A. No. The calculation uses the nominal diameter. Tolerance only sets how far the actual size may sit below nominal.

Q. Why is the scale weight different from the calculated weight?

A. Real diameter, real length, sawn ends and bundle straps all affect the scale. Agree whether the order settles on theoretical or actual weight.

Send the Size List

If you are checking a size list, send the grade, diameter, length, quantity and destination. We will confirm stock, cutting, MTC and the weight basis for the quotation. Use the contact page or the bar quote form to start.

Back to Insights

WAWhatsApp